Printing Error

Re: Printing Error

Postby zxcv555578 » Thu Jun 19, 2014 4:48 pm

Nicholas Seward wrote:Change MAX_ARM_LENGTH to 295mm.

See if that works. If not, tell me what the error messages are. Also, send me your modified Segmentize file. You can attach it here but you have to change the extension from .py to .txt to get it to work.


Also, send me the gcode that you are trying to transform. You might also have to do the extension trick on it too. Is 0,0,0 the middle of your print?

YES, Is 0,0,0 the middle of your print




POINTS=[(160.9,156.1,124),#
(131.9,135.9,169.7),#
(123.9,155.9,159.7),#
(129.6,170.1,141.2),#
(144.8,169.3,128.6),#
(171.3,133.3,130.6),#
(164.7,124.3,144.6),#
(146.5,123.3,164.6),#
]

#DISTANCE FROM SHOULDER SCREW TO SHOULDER SCREW
SIZE=250.0

#APPROXIMATE Z DISTANCE FROM SHOULDER ARM ATTACHMENT
#TO HUB ARM ATTACHMENT
BED_Z=47

#APPROXIMATE MAX ACTUATED LENGTH OF ARM
MAX_ARM_LENGTH=295
zxcv555578
 
Posts: 82
Joined: Sun Jun 15, 2014 9:50 am

Re: Printing Error

Postby zxcv555578 » Thu Jun 19, 2014 4:51 pm

Nicholas Seward wrote:Change MAX_ARM_LENGTH to 295mm.

See if that works. If not, tell me what the error messages are. Also, send me your modified Segmentize file. You can attach it here but you have to change the extension from .py to .txt to get it to work.


Also, send me the gcode that you are trying to transform. You might also have to do the extension trick on it too. Is 0,0,0 the middle of your print?

Calculation of the G code is incorrect, that makes me confused. Where did I go wrong?
My collection point and the center distance of about 25mm,I collected 8 points (8 pieces)
zxcv555578
 
Posts: 82
Joined: Sun Jun 15, 2014 9:50 am

Re: Printing Error

Postby Nicholas Seward » Thu Jun 19, 2014 5:20 pm

Send me your segmentize and your gcode and I will run it on my side.
Nicholas Seward
 
Posts: 738
Joined: Mon Nov 25, 2013 10:41 pm

Re: Printing Error

Postby zxcv555578 » Fri Jun 20, 2014 4:13 am

Nicholas Seward wrote:Send me your segmentize and your gcode and I will run it on my side.

Your e-mail?
I will be sent to your email。 :) :)
zxcv555578
 
Posts: 82
Joined: Sun Jun 15, 2014 9:50 am

Re: Printing Error

Postby Nicholas Seward » Sat Jun 21, 2014 3:15 pm

I gave instructions on how you can attach the gcode and Segmentize above. However, my email is myfirstname.mylastname@gmail.com.
Nicholas Seward
 
Posts: 738
Joined: Mon Nov 25, 2013 10:41 pm

Re: Printing Error

Postby Nicholas Seward » Sun Jun 22, 2014 5:57 pm

Your gcode is centered around (100,100). Open of the gcode and you will see what I am talking about. You need to configure Slic3r to make (0,0) be the center of the print.
Nicholas Seward
 
Posts: 738
Joined: Mon Nov 25, 2013 10:41 pm

Re: Printing Error

Postby zxcv555578 » Sun Jun 22, 2014 6:32 pm

Nicholas Seward wrote:Your gcode is centered around (100,100). Open of the gcode and you will see what I am talking about. You need to configure Slic3r to make (0,0) be the center of the print.

NO,I use 0,0 Print Center。
zxcv555578
 
Posts: 82
Joined: Sun Jun 15, 2014 9:50 am

Re: Printing Error

Postby zxcv555578 » Sun Jun 22, 2014 6:44 pm

Nicholas Seward wrote:Your gcode is centered around (100,100). Open of the gcode and you will see what I am talking about. You need to configure Slic3r to make (0,0) be the center of the print.

I have pictures will be sent to your email :)
zxcv555578
 
Posts: 82
Joined: Sun Jun 15, 2014 9:50 am

Re: Printing Error

Postby Nicholas Seward » Sun Jun 22, 2014 6:55 pm

I opened up your gcode and it is most definetly centered on (100,100)
Nicholas Seward
 
Posts: 738
Joined: Mon Nov 25, 2013 10:41 pm

Re: Printing Error

Postby zxcv555578 » Sun Jun 22, 2014 7:10 pm

Nicholas Seward wrote:I opened up you gcode and it is most definetly centered on (100,100)

That makes me confused :?:
I was set to 0,0
zxcv555578
 
Posts: 82
Joined: Sun Jun 15, 2014 9:50 am

PreviousNext

Return to GUS Simpson

Who is online

Users browsing this forum: No registered users and 1 guest

cron